Umweltsensorik (iWSN)
The iXN-0TH extends an iWSN environmental sensing module with temperature and humidity measurement. It is a good choice where an engineer wants to add these readings to an existing iWSN setup without adding a separate power supply.The module is powered by the iWSN environmental sensing module through the audio line, with a typical consumption of 0.005 W. It measures temperature from -20 ~ +60 °C with 0.1 °C resolution and relative humidity from 10 ~ 95% RH with 0.1% RH resolution. Typical accuracy is ±0.3 °C and ±3% RH between 20 and 80% RH.For installation, the unit can be fixed by wall-mounting or by magnet adsorption. The 27 cm cable and 25 x 20.2 x 30 mm (W x L x H) housing make it straightforward to position for monitoring in environments such as electronics factories.ApplicationsEnvironmental temperature and humidity monitoring in electronics factories
iXN-0VC CR is a CO2e and TVOC sensing module designed to connect to the iWSN environmental sensing module, adding CO2e and TVOC measurement to an existing iWSN installation.The module is energised by the iWSN environmental sensing module through the audio line, so no separate power supply is required. It measures CO2e from 400 ppm to 60000 ppm and TVOC from 0 ppb to 60000 ppb, with resolution that steps up across each range. Its compact 25 x 30 x 20.2 mm housing and 27 cm cable suit installation where the sensor needs to sit away from the host unit.For setup and maintenance, the module can be fitted by wall mounting or by magnet adsorption. It is rated for operation from 0 °C to +45 °C and 10 to 95% RH, non-condensing, and is supplied as an RoHS version with CE and WEEE certification noted.ApplicationsFactory environmental monitoring system
iXN-1CX CR extends an iWSN environmental sensing module with carbon monoxide measurement, covering 0 ppm to 1000 ppm at a resolution of 1 ppm. It is a practical way to add CO monitoring to an existing iWSN installation without designing a separate sensing node.The module is energised by the iWSN environmental sensing module through the audio line, so no external power supply is required. Its power consumption is 0.017 W. It is supplied with a 22 cm cable and can be fitted to a DIN-rail, mounted on a wall, or held in place by magnet adsorption, which simplifies setup and later maintenance.Rated for an operating range of 0 °C to +45 °C and 10 to 95% RH non-condensing, the module carries CE, RoHS and WEEE certifications. Its listed application is factory environmental monitoring.ApplicationsFactory environmental monitoring system
The iXN-2VB3 CR adds 3-axis vibration measurement to an iWSN environmental sensing module. It uses a 3-axis MEMS sensor with a ±8g amplitude range and a 10 Hz to 500 Hz frequency range, and reports RMS and maximum values for the x, y and z axes as well as a triaxial vector value.The module draws its power from the host iWSN sensing module, so no separate supply is needed. Its 150 cm cable and wall-mount or magnet adsorption installation options make it straightforward to position it on rotating equipment for vibration monitoring.Suited to vibration monitoring of rotating systemsOperating temperature range of -25 °C to +75 °CApplicationsVibration monitoring of rotating systems
The SP-S2-DS CR is a dye-sensitised cell charging module based on third-generation solar cell technology. Unlike conventional silicon cells, it keeps generating electricity in low-light conditions such as indoor lighting, and its conversion efficiency is less sensitive to the angle of incoming light.Output is strongest indoors and near windows, so the module suits locations where ambient light is limited. Paired with emergency products, it harvests energy from everyday lighting to support wireless light-charged emergency SOS systems while helping to reduce general power consumption.Power ≥1.67 mW, Voc 0.55 ~ 0.65 V, Isc ≥3.51 mADimensions 133 x 85 x 84 mm (W x L x H)Operating temperature -25 ~ +60 °C, storage -20 ~ +45 °CHumidity 10 ~ 90% RH, non-condensingRoHS and WEEE compliantApplicationsWireless light-charged emergency SOS systems