Accessories

SJ-904 PT100.

2AB125R is a DIP resistor of 125 ohm with a tight 0.1% tolerance and a 1/4 W power rating. Its metal film construction gives a temperature coefficient of 50 ppm/℃, which suits circuits where a stable, well-defined resistance value matters.Engineers typically choose this part when a precise fixed value is needed on a DIP-format board, and the RoHS certification is relevant where compliant components are specified.Resistance: 125 ohmTolerance: 0.1%Power rating: 1/4 WTemperature coefficient: 50 ppm/℃

Antenna Extension Cable, RG58A/U, RP-SMA Male to RP-SMA Female, 1M.

Antenna Extension Cable, RG58A/U, SMA Male to SMA Female, 1M.

Antenna Extension Cable, RG58A/U, RP-SMA Male to RP-SMA Female, 3M.

HDF 200 cable, 1 meter long N type male to RP-SMA male.

HDF 200 cable, 3 meter long N type male to RP-SMA male.

Antenna Extension Cable, RG58A/U, RP-SMA Male to RP-SMA Female, 5M.

HDF 200 cable, 5 meter long N type male to RP-SMA male.

Antenna Extension Cable, RG58A/U, SMA Male to SMA Female, 5M.

Antenna Extension Cable, RG58A/U, SMA Male to SMA Female, 10M.

Antenna Extension Cable, RG58A/U, RP-SMA Male to RP-SMA Female, 8M.

IP67 RJ45 Plug.

Cap with Tether.

IP67 Power Plug (5-pin).

IP67 Power Plug (3-pin).

ADP-20 CR is a 20-pin to 20-pin connector extender for ISA cards. It relays the dual 20-pin flat cable connection away from the card, so the wiring can be routed to a more convenient position within a cabinet or test setup.The kit includes one CA-2002 flat cable, 20-pin, 20 cm long (one set of two cables). The board measures 114 mm x 102 mm and is rated for operation from 0 to +60 °C, with storage from -30 to +80 °C and a humidity range of 10% to 90%, non-condensing.The board is listed under DAQ daughter boards. The manufacturer also lists the ADP-20/PCI as a similar item for comparison. The ADP-20 CR is RoHS and WEEE certified.ApplicationsExtending 20-pin flat cable connections on ISA cards

ADP-20/PCI CR is a 20-pin to 20-pin connector extender for PCI card wiring. It carries a dual 20-pin flat cable connection over a longer run, so the card can be reached from a more convenient location.The kit includes one CA-2002 flat cable set, 20-pin, 20 cm long, supplied as two cables. This lets you start wiring straight away without sourcing a matching cable separately.The extender is RoHS compliant. It belongs to the DAQ daughter board accessory range, so it suits engineers building or servicing data acquisition setups that use PCI cards.

The ADP-37 CR is a connector extender that brings a 50-pin Opto-22 header out to a female DB-37 connector, giving engineers a practical way to wire Opto-22 signals to an ISA data acquisition card.The kit includes a 20 cm, 50-pin CA-5002 flat cable, so the board can be connected straight away. Its compact 114 mm x 102 mm footprint suits tight enclosures and benchtop setups.Compliant with RoHS and WEEE, the ADP-37 CR is rated for an operating temperature of 0~ +60 °C and storage of -30 ~ +80 °C, with 10% ~ 90% humidity, non-condensing.ApplicationsWiring Opto-22 signals to a DB-37 connector on an ISA card

The ADP-37/PCI CR is a connector adapter that brings a 50-pin Opto-22 interface out to a female DB-37 connector, making it easier to wire field signals to a PCI data acquisition card. It is supplied with a CA-5002 flat cable, 50-pin, 20 cm long, so it can be connected straight away.The board measures 114 mm x 102 mm and is rated for an operating temperature of 0 ~ +60 °C, with a storage range of -30 ~ +80 °C. Relative humidity of 10% ~ 90% is permitted, non-condensing. The product is RoHS and WEEE listed.Choose this variant when your system uses a PCI card and you need a 50-pin Opto-22 to DB-37 breakout. For the ISA card version, check the separate ADP-37 CR listing.ApplicationsWiring 50-pin Opto-22 signals to DB-37 connectors on PCI data acquisition systems

The ADP-50 extends a single 50-pin flat cable connection on an ISA card, letting you position the connector away from the card's original location. It is a passive adapter with no electronics of its own, so it adds no configuration or software requirements.Supplied with the CA-5002 cable: the order includes a 50-pin flat cable, 20 cm long, so the extender can be used straight out of the box in a typical DAQ setup.The board measures 114 mm x 102 mm and is specified for an operating temperature of 0~ +60 °C, with storage between -30 ~ +80 °C and humidity of 10% ~ 90%, no condensing. It is RoHS and WEEE certified. For a PCI-based variant, see the ADP-50/PCI.ApplicationsExtending a 50-pin flat cable connection on ISA data acquisition cardsPositioning I/O connectors away from the ISA card inside an enclosure or cabinet

ADP-50/PCI CR is a 50-pin to 50-pin connector extender for PCI card installations, used to extend a 50-pin flat cable run where the existing reach is insufficient or the connection point needs to move.The kit includes a CA-5002 flat cable (50-pin, 20 cm), so it can be fitted straight away. The extender is compact at 114 mm x 102 mm and is RoHS and WEEE certified.Operating range is 0 ~ +60 °C, with storage between -30 ~ +80 °C and humidity of 10% ~ 90%, non-condensing. Check the environmental limits against your cabinet conditions before installation.ApplicationsExtending 50-pin flat cable connections on PCI card installations

AFAN-02 CR is a 1U two-way cooling fan module that keeps equipment within its temperature limits by providing active air movement. It accepts two fan modules, so a failed unit can be replaced while the system keeps running.Each fan has its own fault LED, and the relay alarm output signals a fan failure or loss of power. A failure in one fan does not affect the other, and a 5A fuse with overvoltage protection guards the 24 VDC supply.Relay alarm output reports fan failure or power loss to a remote monitoring systemMounted on a wall, the unit is suited to small server cabinetsApplicationsCooling for small server cabinets

The AFAN-04 CR is a 1U cooling fan module for rack-mounted computer room and industrial equipment. It houses four fans that provide active airflow, helping to lower the operating temperature of the equipment and maintain stable operation.Each fan has its own fault LED, and a relay alarm output signals any fan failure or loss of power to a remote monitoring system. Because a single fan failure does not affect the others, the module keeps cooling while a faulty unit is identified and replaced. The fans are hot-swappable, so maintenance can be carried out without shutting down the equipment.The module runs from 24 VDC with a 5A fuse for overvoltage protection and is sized for 19-inch racks. It is suited to engineers specifying thermal management for server rooms and control cabinets, where fan faults must be detected early to avoid overheating.ApplicationsCooling of computer room and server room equipmentThermal management of industrial equipment in 19-inch cabinetsFan fault monitoring with remote alarm signalling