ZigBee

The tZT-P4C4 is a compact ZigBee router that brings four isolated digital inputs and four isolated digital outputs onto a 2.4 GHz wireless link. It suits remote switch and status monitoring, or switching of loads, at points where running cable is difficult or costly. Each channel is photocoupler isolated, and the module offers 3750 VDC intra-module isolation.The digital inputs are source-type wet contacts with a 100 Hz frequency rating, and each channel can be configured as a 16-bit counter with a maximum count of 65535. The outputs are isolated open-collector, sink-type channels rated at 700 mA per channel, with overvoltage and overload protection. Power-on and safe output values are programmable, so outputs can be set to a defined state at start-up or when communication is lost.The module is fully compliant with the ZigBee 2007 Pro and IEEE 802.15.4 specifications and can act as a repeater to extend the network. Wireless traffic is protected with AES-128 encryption. Configuration is carried out with the Windows GUI configuration software. Supported protocols are DCON and ModBus. Note that this ordering code is listed for Asia only.ApplicationsRemote monitoring of switches and dry or wet contacts in hard-to-wire locationsWireless switching of loads through isolated sink-type outputsEvent and pulse counting over a wireless link using the 16-bit counter inputs

The ZT-2005-C8 is an 8-channel thermistor input module that also works as a ZigBee router, so it can measure temperature at remote points and relay readings within a personal area ZigBee network built on IEEE 802.15.4. Each channel delivers 12-bit resolution with ±1 °C accuracy, with a total sampling rate of 10 Hz.The module suits distributed temperature monitoring where cabling is impractical. It supports the ZigBee repeater function and both DCON and Modbus RTU protocols, uses AES-128 encryption and has a typical line-of-sight range of 700 m. Module address, protocol, checksum, ZB-PID and ZB-channel are set with rotary and DIP switches.Power is supplied from +10 VDC to +30 VDC at 1 W maximum. The unit provides 1000 VDC intra-module isolation and 4 kV ESD protection, mounts on DIN-rail and operates from -25 °C to +75 °C. This ordering code includes one thermistor probe (φ6x60 mm stainless steel pipe, 4.94 m wiring). The ordering information specifies Asia only.ApplicationsWireless temperature monitoring in personal area ZigBee networksRemote temperature measurement where wired connections are impractical

The ZT-2015 CR is a wireless RTD acquisition node that lets engineers collect temperature readings from six channels without running signal cabling back to a controller. It operates in the ISM 2.4 GHz band and acts as a ZigBee router, so it can extend a wireless network while it reports its own measurements.Each channel accepts 2-wire or 3-wire RTD sensors and can be configured individually. The 3-wire lead resistance elimination keeps readings accurate over long cable runs, and open wire detection and overvoltage protection (120 VDC/110 VAC) help protect the module and flag faulty connections. Address, protocol, checksum, ZB-PID, ZB-channel and type code are set with rotary and DIP switches, and a Windows GUI configuration utility is available.With a stated line-of-sight range of 300 m to 700 m, depending on the RF power setting, and 3000 VDC intra-module isolation, the ZT-2015 CR suits distributed temperature monitoring in building, factory and machine automation, as well as remote maintenance and diagnosis tasks.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The ZT-2017 CR lets engineers bring eight differential analog signals onto a ZigBee wireless network without running signal cable back to a controller. Each channel converts with 16-bit resolution and can be given its own input range, from ±150 mV up to ±10 V, with current inputs of ±20 mA, 0 ~ 20 mA and 4 ~ 20 mA available using an optional external 125 Ω resistor.Field wiring is protected by 240 Vrms overvoltage protection and ±4 kV contact ESD protection on each terminal, with an intra-module isolation rating of 3000 VDC. Addressing, protocol, checksum and type code settings are made with rotary and DIP switches, and the GUI configuration software for Windows adjusts the RF transmission power and other parameters.This is the ZigBee Router variant, supporting DCON and Modbus RTU and rated for a line-of-sight range of 300 m to 700 m depending on RF power setting. The ordering information lists it as Asia only, so please confirm availability for your project before ordering.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The ZT-2017C CR is a wireless analog input module for remote current measurement over ZigBee. It provides eight differential channels with 16-bit resolution, and each channel can be set to its own range: -20 mA to +20 mA, 0 to +20 mA or +4 to +20 mA. Open wire detection for 4 to 20 mA inputs helps engineers spot broken sensor wiring without additional hardware.Configuration is handled with the external DIP and rotary switches, which set the module address, protocol, checksum and type code, or with the GUI configuration software for Windows. The module supports DCON and Modbus RTU and is listed as a ZigBee 2007 Pro device. Its transmission range is stated as 300 m to 700 m line of sight, depending on the RF power setting, which is adjustable from 10 dBm to 19 dBm EIRP.For electrically noisy or high-voltage installations, the module offers ±200 VDC common voltage protection, 3000 VDC intra-module isolation and ±4 kV ESD contact protection on each terminal. It mounts on a DIN rail and is powered from +10 to +30 VDC. The manufacturer describes this model as Asia only, so please check its availability before specifying it for other regions.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

ZigBee Wireless 8-ch Thermocouple Input Module with High Voltage Protection (ZigBee Router). (Asia Only) (Included CN-1824 Daughter Board x 1).

ZT-2024 CR is a ZigBee router module that brings four 12-bit analogue outputs into a wireless network. Each channel can be set independently to 0 ~ +10 VDC, -10 VDC ~ +10 VDC, 0 ~ +5 VDC, -5 VDC ~ +5 VDC, 0 ~ +20 mA or +4 mA ~ +20 mA, which makes it suited to driving actuators, valves and drives where cabling is impractical.The module supports DCON and Modbus RTU protocols and is compliant with the ZigBee 2007 Pro standard, with up to 255 slaves supported. Transmission power is adjustable from 10 dBm to 19 dBm (EIRP) using the utility, giving a line-of-sight range of 300 m to 700 m depending on the RF setting. Module address, protocol, checksum, ZT-PID, ZT-channel and type code are set with the external DIP and rotary switches, and a Windows GUI configuration utility is also available.For fail-safe operation, each channel has configurable power-on and safe output values, and a watchdog timer monitors the module and communication. The unit is DIN-rail mounted, operates from +10 VDC to +30 VDC and is rated for -25 °C to +75 °C. The manufacturer lists this variant for Asia only, so confirm regional availability before ordering.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The ZT-2026 CR is a ZigBee wireless I/O module that acts as a router and combines four differential analogue inputs, two analogue outputs, two wet-contact digital inputs and two isolated open-collector digital outputs in one DIN-rail unit. Each analogue input can be set to its own range, from ±10 V down to ±150 mV or -20 mA to +20 mA, and every input channel is protected against overvoltage up to 240 Vrms.The module suits engineers who need to extend I/O across a building, plant or machine without running cable between points. It works over the 2.4 GHz ISM band with ZigBee 2007 Pro, with a line-of-sight range of 300 m to 700 m depending on the RF power setting. Address, protocol, checksum and type settings are made with DIP and rotary switches, and the Windows GUI configuration software is available for further setup.Safety-related outputs can be given a power-on value and a safe value, and the module provides 2500 VDC intra-module isolation along with ±4 kV contact ESD protection on each terminal. The manufacturer lists this ordering variant for Asia only, so check regional availability before specifying it for European projects.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

The ZT-2042 CR is a ZigBee wireless I/O module that combines four PhotoMOS relay outputs with four sink-type open-collector digital outputs. It acts as a ZigBee router and supports the repeater function, so it can extend a wireless network while switching loads at remote points.Each output channel is photo-coupled, and the module provides 3000 VDC intra-module isolation and ±4 kV ESD protection on the communication line and each channel. Short circuit and overload protection, surge protection and configurable power-on and safe output values help keep control logic predictable when links or power are disturbed.Module address, protocol and ZigBee channel settings are made with rotary and DIP switches, with a Windows GUI configuration utility also available. The unit supports DCON and Modbus RTU, and the source lists it as Asia only.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

ZT-2043 CR is a wireless digital output module that switches 14 channels remotely over a ZigBee network. The CR suffix denotes the ZigBee Router variant, which can also act as a repeater to extend the reach of a mesh. Each channel is a sink-type open-collector output with photo-coupler isolation, so the module can drive external loads without sharing a ground reference with the controller.The module operates in the 2.4 GHz ISM band and is designed for ZigBee 2007 Pro. Transmit power can be adjusted between 10 dBm and 19 dBm EIRP, and the line-of-sight range is quoted as 300 m to 700 m depending on the RF setting. Each output has short circuit and overload protection, and power-on and safe values can be configured so that outputs take a defined state on start-up or on communication loss.Configuration is done with DIP and rotary switches for address, protocol and channel settings, or with the Windows GUI configuration software. Communication uses DCON or Modbus RTU, and the module is intended for DIN-rail installation. The manufacturer lists this variant as Asia only.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

ZT-2043-IOG is a ZigBee wireless module from the ZT-20xx-IOG series, providing 14 isolated digital output channels. Its I/O Group design lets several ZT-IOG nodes work together so that output states across the network follow input changes elsewhere, without a hard-wired link between them.Each module can be set as a ZigBee Coordinator or a ZigBee Router using the external switches. The Coordinator processes incoming events and calculates the resulting output states, then periodically broadcasts them to the Router modules so all digital outputs stay synchronised. The pairing relationships between I/O channels are configurable.Choose this variant when you need wireless switching of 14 open-collector sink outputs with 3750 VDC intra-module isolation and a 10 to 30 VDC supply. The shop listing for this ordering code is marked as Asia only by the manufacturer.ApplicationsWireless digital output control across multiple remote pointsSynchronised switching of outputs driven by inputs on other ZT-IOG nodesDistributed I/O where cabling between machines or panels is impractical

The ZT-2052 CR is a ZigBee router module that brings eight isolated wet-contact digital inputs into a wireless network. Each input is photocoupler-isolated, and sink or source wiring is selected through the field connections, so the module suits a range of sensor and switch types.Every channel can operate as a 16-bit counter (up to 65535 counts), with a 100 Hz frequency and a 5 ms minimum pulse width. Address, protocol, checksum and ZB settings are chosen with the rotary and DIP switches, or adjusted through the Windows GUI configuration software. The module can also act as a ZigBee repeater to extend coverage.Engineers typically choose the ZT-2052 CR for remote monitoring and diagnosis in building and factory automation, where wiring long runs to a central controller is impractical. It supports DCON and Modbus RTU, with up to 255 slaves.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

ZT-2052-IOP is a ZigBee coordinator with eight isolated wet-contact digital inputs. Its embedded I/O binding links each input channel to a corresponding digital output on a ZT-2042 remote module (4-ch PhotoMOS relay output and 4-ch open collector), so no external controller is needed to pair the channels.The module continuously sends input status updates to the ZT-2042 to keep its outputs synchronised. Wireless transmission range is up to 700 m by default and RF output power is adjustable from 10 dBm to 19 dBm EIRP. AES-128 encryption protects the wireless link, and a DO safe value setting supports monitoring of wireless disconnection.External DIP and rotary switches allow configuration without software, which suits sites where running wiring is difficult. The unit operates from -25 ~ +75°C, mounts on DIN-rail and provides surge and ESD protection.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The ZT-2053 CR is a ZigBee wireless digital input module that collects 14 channels and passes their status across a 2.4 GHz ZigBee network. Each channel accepts either dry or wet contact signals, so one unit can monitor switches and relay contacts as well as wet logic inputs from +3.5 VDC to +30 VDC.All 14 channels can be used as 16-bit counters (maximum 65535), with a 100 Hz frequency and a minimum pulse width of 5 ms. The module provides 4 kV ESD protection, surge protection and 3750 VDC intra-module isolation, with a LED indicator for each input channel.Settings for module address, protocol, checksum, ZB-PID and ZB-channel are made with DIP and rotary switches, and RF output power can be adjusted through the Windows GUI configuration software. The unit supports the ZigBee Repeater function and both DCON and Modbus RTU protocols.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

ZT-2053-IOG CR is a ZigBee I/O module configured as the coordinator of an IOG pair-connection network. It monitors 14 isolated digital inputs and handles the logic that decides which remote outputs should change state, so that inputs on one module can drive outputs on others without wiring between them.Any change of state on a digital input is reported immediately to the coordinator, which evaluates the I/O mapping and returns the resulting output states. The coordinator then sends periodic broadcasts to the ZT-IOG router modules so that their outputs stay synchronised with the network.Suited to distributed input monitoring over 2.4 GHz ZigBee links with AES-128 encryption.Pair-connection mapping is configurable, so the relationships between inputs and outputs can be adjusted to suit the installation.ApplicationsWireless distributed digital input monitoringMulti-to-multi I/O pair-connection between remote ZT-IOG modules

The ZT-2053-IOP CR is a ZigBee coordinator that reads 14 digital input channels and wirelessly drives the matching outputs on a remote ZT-2043 module. Its embedded I/O binding handles the channel pairing, so engineers can synchronise remote outputs with local inputs without adding a separate controller. Each input channel's state is sent continuously, keeping the remote outputs aligned.Inputs accept both dry and wet contacts, and the module provides 3750 VDC intra-module isolation. RF output power is adjustable from 10 to 19 dBm EIRP, giving a line-of-sight distance of 300 to 700 m depending on the setting. Encryption uses AES-128, and up to 255 slaves are supported under the ZigBee 2007 Pro standard.External DIP switches allow configuration on site, which suits installations where wiring is difficult. The module mounts on a DIN rail and operates from -25 to +75 °C. The manufacturer's description lists it as Asia only.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

The ZT-2055 CR is a ZigBee router module that adds 8 isolated digital inputs and 8 digital outputs to a wireless network, letting engineers monitor and switch remote field signals without running cable back to a controller. The CR suffix identifies the ZigBee Router variant. This listing is for the Asia-only version.Each digital input can be wired as dry contact or wet contact, and all inputs can be used as 16-bit counters with a maximum count of 65535. The outputs are sink-type open collector channels with overload protection, and power-on and safe values are programmable so outputs can be held in a defined state.The module is configured with DIP and rotary switches, with a Windows GUI configuration utility also available. It supports DCON and Modbus RTU, and includes ZigBee repeater functionality, AES-128 encryption for wireless communication, and DIN-rail mounting.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The ZT-2055-IOG CR is a ZigBee wireless I/O module that combines eight isolated digital inputs and eight isolated digital outputs in one DIN-rail unit. It is built for multi-to-multi pair-connection, where a change on any input in the network can determine the output states of other modules without running cables between them.Each module can be set as a ZigBee Coordinator or a ZigBee Router using external switches. The Coordinator receives input events from the network, calculates the resulting output states across the system and periodically broadcasts them to the Router modules, keeping all digital outputs synchronised.Wireless traffic is protected with AES-128 encryption, and the RF output power can be adjusted, with a default transmission range of up to 700 m. A configurable DO safe value helps monitor wireless disconnection. The manufacturer lists this ordering code as Asia only, so check regional eligibility before ordering.ApplicationsWireless distributed digital I/O between machines or equipmentMulti-point input-to-output control logic across a ZigBee networkRemote switching and status monitoring where cabling is impractical

ZT-2055-IOP CR is a ZigBee coordinator module that links remote digital I/O over the 2.4 GHz ISM band. Each of its 8 isolated digital inputs and 8 open-collector digital outputs can be paired with a channel on a remote ZT-2055, so engineers can mirror switch states across a site without adding a PLC or PC to manage the link.The module continuously updates the outputs of the remote ZT-2055 from its own inputs, and reads the remote inputs to drive its own outputs. The DO safe value setting lets the output state be defined for wireless disconnection monitoring, and external DIP switches allow the signal synchronisation to be configured on site where wiring is awkward.The manufacturer lists this ordering code for Asia only. Please check regional availability before specifying it for European projects.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

ZT-2060 CR is a wireless remote I/O module that combines six digital inputs with four Form A power relay outputs. It communicates over the 2.4 GHz ZigBee 2007 Pro network and can act as a ZigBee router to extend the wireless network, which makes it suited to remote sensing and switching where cabling is impractical.Each digital input is photocoupler isolated and can be wired as sink or source, and the inputs can also be used as 16-bit counters with a maximum count rate of 100 Hz. The relay outputs are rated at 5 A at 250 VAC or 30 VDC, and both power-on and safe output values are programmable. Address, protocol and ZigBee settings are configured through DIP and rotary switches, with a Windows GUI utility available for further setup.Note that the manufacturer lists this variant for Asia only. Please check the specification and regional requirements before specifying it for European projects.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

The ZT-2060-IOG CR is a ZigBee wireless I/O module for building pair-connection systems, in which digital inputs on one module drive relay outputs on others. It combines six isolated wet-contact digital inputs with four Form A power relays rated at 5 A, so a single unit can both sense field signals and switch loads.Each module can be set as a ZigBee Coordinator or a ZigBee Router using external switches. The Coordinator processes and distributes messages: any DI state change is reported to it, it calculates the resulting DO states across the system, and it periodically broadcasts those states to the Router modules so that all relay outputs stay synchronised.For installation and resilience, the unit offers configurable I/O pairing, a safe value setting for relay outputs when wireless communication is lost, AES-128 encryption for wireless traffic and adjustable RF output power. It mounts on DIN-rail, runs from +10 VDC to +30 VDC at up to 1.4 W and operates from -25 to +75 °C.ApplicationsWireless multi-to-multi I/O pairing between distributed digital inputs and relay outputsRemote switching of loads through 5 A power relay outputsWireless monitoring of digital input states across a ZigBee network

The ZT-2060-IOP is a ZigBee coordinator that combines four isolated digital inputs with four power relay outputs. Its embedded I/O channel binding links each channel's status to a remote channel of the ZT-2060, so engineers can set up wireless input-to-output pairing without an external controller.The module continually updates the remote ZT-2060's digital outputs from its own inputs, and reads the remote inputs to synchronise its own relays. External DIP switches allow quick configuration on site, which helps where wiring conditions are difficult. The DO safe value supports wireless disconnection monitoring, and AES-128 encryption protects the wireless link.The manufacturer lists this variant for Asia only, so check regional suitability before specifying it for a European project.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment